DigitSmith

Anybody in forum familiar with DAHAO controllers

Like Tree1Likes
  • 1 Post By AJST

Reply
 
Thread Tools Search this Thread
Old April 28th, 2013, 12:39 AM   #1 (permalink)
Gabriel Gabriel is offline
Member
Join Date:
Sep 2009
Posts:
79
Liked:
3 times
Default Anybody in forum familiar with DAHAO controllers

Hello
Im having issues with my machine with DAHAO control, anybody familiar with them?
Send a private message to Gabriel ContactReply & Quote
Old April 28th, 2013, 10:44 AM   #2 (permalink)
AJST AJST is offline
Senior Member

AJST's Avatar
Join Date:
Jun 2011
Location:
Based in Georgia- Travel to anywhere in U.S.A.
Posts:
147
Liked:
19 times
Default Re: Anybody in forum familiar with DAHAO controllers

I know them pretty well, how can I help?
dolphinsatsea likes this.
__________________
AJ’s Stitchin’ Time
Dennis Wilson
Embroidery Machine Technician
www.ajstitch.com [email address]
Send a private message to AJST ContactReply & Quote
Old May 5th, 2013, 02:38 AM   #3 (permalink)
Gabriel Gabriel is offline
Member
Join Date:
Sep 2009
Posts:
79
Liked:
3 times
Default Re: Anybody in forum familiar with DAHAO controllers

Hello Thanks for your reply.
I have a BECS119 controller which lost memory and I was told to replace battery to get it back up and running. Replaced battery and noticed all parameters were not properly set. I had to set them up one by one. I finally had my embroidery head running but my chenille head wont trim neither move needle bar. All other functions work just fine. When trying to see why these two functions were not performing I followed where these 2 step motors were connected to and found that they are connected to a board E924D which is the chenille board head. Machine has 2 of these cards and these 2 motors are connected exactly to the same connector on each card. I wonder if there is a setup procedure to reset these boards.
The color change motor, the tension release motor and D axes motors are connected to these boards and are working fine. The main shaft motor is also working fine.
Im stuck because machine wont sew.
Send a private message to Gabriel ContactReply & Quote
Old May 8th, 2013, 06:30 AM   #4 (permalink)
AJST AJST is offline
Senior Member

AJST's Avatar
Join Date:
Jun 2011
Location:
Based in Georgia- Travel to anywhere in U.S.A.
Posts:
147
Liked:
19 times
Default Re: Anybody in forum familiar with DAHAO controllers

Hey Gabriel,

You may want to contact me by email [email address] . I haven't checked these post in a few days.

You will need to find the specific settings for your machine. Those settings and parameters should be in the owners manual that came with the machine or from Dahao. What brand and model is your machine?
__________________
AJ’s Stitchin’ Time
Dennis Wilson
Embroidery Machine Technician
www.ajstitch.com [email address]
Send a private message to AJST ContactReply & Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
Anyone familiar with Brown Mfg. Pony & Air Pony Dryers GorillaWhite Screen Printing 4 May 3rd, 2011 03:24 PM
Debate Forum Or Selling Forum Mike Evans General Discussions 5 January 30th, 2011 05:25 PM
Wilcom Keyboard Font Forum efect Product/Service Promotion 0 January 19th, 2011 11:34 AM
Embroidery Font Forum efect Product/Service Promotion 0 April 8th, 2010 02:30 PM

All times are GMT -4. The time now is 01:51 PM.
Copyright © 2011 DigitSmith. All rights reserved.
Forums software by VBulletin, Copyright © 2000-2024, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.