ECRM-VRL 45 Imagesetter and Glunz & Jensen inline film processor

Prints of ATL

Used but fully functional imagesetter, including a Harlequin RIP. Sold new for $65,000 . I paid $25,000 when it was six years old.Will sell for $5000 or best offer.

Also have a separate 1996 Glunz & Jensen K-550 inline film processor which I will sell for $1500(needs bridge repair)

IMAGESETTER SPECS:
Dimensions: 28"W x 40.5"D x 17"H

Weight:150 lbs
Power requirements: Heat dissipation: Recording source: Spot size:
Density uniformity: Repeatability:

Available resolutions and imaging speed:

Record image width: Output media:

Take-up cassette:

VR45 and VRL45: Basic engine: 28"W x 40.5"D x 17"H ( 711mm x 1029mm x 431mm)
VR45 and VRL45: 150 lbs. (68 Kg)
115/230V (#10%), 3.0/1.5 amps, 50/60 Hz, single phase
1000 BTU/hr. maximum
VRL:One10mWvisibleredlaserdiode(670nmrecordingwave length) VR:One10mWinfraredlaserdiode(780nmrecordingwavelen gth) .001" (25 microns)

Within .3D on 100% dot

VR45 and VRL45: #.0015" (.04mm) typical over 18" x 24". May vary according to media, media packaging and processing conditions.

2,540 dpi: 4.1"/min; 2,400 dpi: 4.4"/min; 2,032 dpi: 5.2"/min; 1,800 dpi: 5.8"/min; 1,524 dpi: 6.9“/min; 1,446 dpi: 7.3”min; 1,270 dpi: 8.3 "/min; 1,200 dpi: 8.7"/min; 1,016 dpi: 10.3"/min; 1,000 dpi: 10.5"/min.

VR45 and VRL45: Up to 18.157" (461.2mm)

Visible red sensitive film or IR sensitive film (polyester base), paper or plate material, .004" to .007" thick - emulsion in, rolled on 2" I.D. heavy duty core. Maximum outside diameter: 4.3" (109mm). Selectable adjustment for .004" or .007" media. Roll capacity up to 200' (60m), including the following standard widths: 18.1" (460mm) and 18" (457mm) - VR45 and VRL45; 14.0"(355mm), 12.2" (310mm), and 12" (305mm) - VR36, VRL36, VR45, and VRL45. Supply cassettes are darkroom loaded (green safety light); capacity one roll, available for following media widths: 18.1"/18" - VR45 and VRL45 only, 14” or 12.2”/12” - VR36, VRL36, VR45, and VRL45.

Capacity 25ft (7.6m) film; 20ft (6.1m) paper; 7 mil plate material requires an on-line processor.

ECRM RIP Specifications

Power Mac configurations (confirm with dealer or ECRM customer service)

Recommended PC Configuration fully dedicated PC:
Note:
Due to the wide variety of PC platforms, please consult

with your dealer or ECRM before purchasing a PC RIP workstation.

Network Interfaces: Features:

System Components:

System Fonts:

Recommended Configuration:

• Power Mac 9500/132 or 9500/120
• Macintosh system software 7.5 or higher
• 72MB total RAM (minimum)
• 1.0GB or larger SCSI II hard disk with 10ms (or faster)

average seek time and 5MB/sec sustained data rate • Uses PelBox/SCSI adapter kit (required)

• Intel Pentium (90 MHz minimum)
• 32-bit PCI bus
• Adaptec 2940 disk controller (Required; no substitutions) • 1.0 GB (minimum) fast (10MB/s) SCSI-2 hard disk

with <10ms average seek time, 7200 RPM spindle speed • SVGA graphics card w/1MB RAM and SVGA monitor

(800 x 600 x 16 colors recommended resolution) • SMC EtherCard Elite 16 network interface board • Adaptec EZ-SCSI 3.11 or higher

Alternative Configuration:

• Power Mac 8100/80
• Macintosh system software 7.1.2 or higher
• 72MB total RAM (minimum)
• 1.0GB or larger internal SCSI II hard disk with 10ms (or faster)

average seek time and 5MB/sec sustained data rate
• Available full length NuBus slot for PelBox Nubus interface kit, or

uses PelBox/SCSI adapter kit

• 64MB RAM (expandable to 128MB) w/256K RAM cache; refresh rates as recommended by system board manufacturer

• Microsoft compatible mouse
• Serial (Com port), parallel printer port
• 3.5” floppy drive
• Enhanced keyboard
• MS-DOS 6.2 or higher
• Windows for Workgroups 3.11 or higher

Works as a Chooser-level print device on an EtherTalk network (both Macs and PCs), or prints files from a network spool folder. PCs require a network interface board (SMC EtherCard Elite 16 recommended).

• Level 2 PostScript® - language compatible
• Easy to use menus; RIP monitor provides status of jobs
• Folder queuing prints all files from a specified folder or directory
• Precision screens for moiré-free color separations
• Preview option allows you to quickly RIP a job to view on the computer screen
• Built-in calibration; RIP can be calibrated on a stand-alone computer; Easy to use exposure test
• Parallel page processing for fast, productive throughput
• Option to store RIPed jobs as compressed files for fast re-imaging and multi-copy imaging
• Film saving option automatically orients image on media
• Media management feature provides input and output cassette film counting; image positioning for direct to plate applications • ECRM FM Screening option

pro graphics

Do you still have this equipment?