DigitSmith

Melco emc6 help

Like Tree1Likes
  • 1 Post By AlisonB

Reply
 
Thread Tools Search this Thread
Old September 13th, 2012, 01:19 AM   #1 (permalink)
Otoraya Otoraya is offline
Junior Member
Join Date:
Sep 2012
Posts:
1
Liked:
0 times
Default Melco emc6 help

Ive replaced the Entire sewing head of my melco emc 6 black head. But I can't get it to do a "head up" and I keep getting an error message "z timeout error." As the machine starts up, the cilinoid fires once and the head response as well but after that I cannot get any response from it, I tried head timing menu function and z timeout error continues to show I have also tried the function without the needle head on and off and no luck. Does any one have any suggestions?

Thanks
Oscar T.
Send a private message to Otoraya ContactReply & Quote
Old September 18th, 2012, 02:51 PM   #2 (permalink)
BJ24 BJ24 is offline
Member
Join Date:
Sep 2012
Location:
Seattle
Posts:
88
Liked:
3 times
Default Re: Melco emc6 help

Have you tried getting it up manually? I have had that happen and I used a flat head screw driver and turn the area on the right side of the head that allows you to manually change the color position. Sometimes that will trigger it to head up or it will release it and then try the head timing menu function.
Hope that is of help.
BJ
Send a private message to BJ24 ContactReply & Quote
Old August 12th, 2016, 10:39 PM   #3 (permalink)
funtosee funtosee is offline
Junior Member
Join Date:
Aug 2016
Posts:
1
Liked:
0 times
Default Re: Melco emc6 help

My machine is doing the same thing! Did you get yours fixed? What was the problem?
Send a private message to funtosee ContactReply & Quote
Old January 11th, 2019, 02:40 AM   #4 (permalink)
Namelesspick51 Namelesspick51 is offline
Junior Member
Join Date:
Oct 2018
Posts:
1
Liked:
0 times
Default Re: Melco emc6 help

I bought 2 of the single head tajima machines but I don't have a manual I did get them communicating with my computer and I have design shop 7 but I don't know how to thread this machine. It's different than the white head melco. Any help would be appreciated greatly
Send a private message to Namelesspick51 ContactReply & Quote
Old February 4th, 2019, 01:28 PM   #5 (permalink)
Ramon Ramon is offline
Junior Member
Join Date:
Feb 2019
Posts:
1
Liked:
0 times
Default Re: Melco emc6 help

I HAVE A MELCO MACHINE EMC1 BUT I DO NOT HAVE HOW TO SPEND IT, NOT IF ANYONE COULD HELP ME
Send a private message to Ramon ContactReply & Quote
Old February 5th, 2019, 01:57 AM   #6 (permalink)
AlisonB AlisonB is offline
Senior Member
Join Date:
Oct 2010
Location:
South Africa
Posts:
115
Liked:
23 times
Default Re: Melco emc6 help

Ramon, not sure what you are asking.
You don't know how to ? it? (Thread it? Start it? Sell it?) Somewhere there is a translation problem.
Robert Young likes this.
Send a private message to AlisonB ContactReply & Quote
Old February 7th, 2019, 08:08 AM   #7 (permalink)
Robert Young Robert Young is offline
Senior Member

Robert Young's Avatar
Join Date:
Oct 2007
Location:
Harlingen, TX
Posts:
1,354
Liked:
171 times
Default Re: Melco emc6 help

Ramon please clarify and i bet several on this forum can help. I personally cannot as I am not familiar with that machine since my last Melco was a Superstar... * meaning old. ha.
__________________
Modern Embroidery Designer
www.volant-tech.com
www.volantfineart.com
Send a private message to Robert Young ContactReply & Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
Melco EMC6 (melco white head) Embroidery machine bigmacatac Used Embroidery Machines 8 February 4th, 2019 01:26 PM
Melco EMC6 (melco white head) Embroidery machine bigmacatac Used Embroidery Machines 3 December 5th, 2012 02:38 PM
Melco Emc6 Embroidery Machine $3,500 bigmacatac Old Embroidery Ads 4 February 7th, 2012 09:18 AM
troubleshooting for my melco EMC6 !! sewcrazy Embroidery and Digitizing 4 November 4th, 2009 09:42 PM

All times are GMT -4. The time now is 11:04 PM.
Copyright © 2011 DigitSmith. All rights reserved.
Forums software by VBulletin, Copyright © 2000-2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.