DigitSmith

Prodigi Help!!!

Reply
 
Thread Tools Search this Thread
Old December 18th, 2014, 11:59 AM   #1 (permalink)
kyclover6035 kyclover6035 is offline
Junior Member
Join Date:
Aug 2014
Posts:
2
Liked:
0 times
Default Prodigi Help!!!

I currently have a Prodigi machine and keep getting error code 70 - can not locate 210 pos.

HELP!!!
Send a private message to kyclover6035 ContactReply & Quote
Old December 19th, 2014, 07:42 AM   #2 (permalink)
aardvark7 aardvark7 is offline
Member
Join Date:
Jul 2014
Posts:
55
Liked:
12 times
Default Re: Prodigi Help!!!

All embroidery machines have various position coders to let the machine know where the needle bar is, so that trimming, jumping, and moving the frame don't happen while the foot is down, or the needle is through the fabric.

It may be that the relevant coder has a fault or has been knocked out of alignment.

The first thing to do is try a machine reset. The procedure should be in the manual but the supplier will guide you through if you don't have one. Do remember to change back any settings if you have them different from default.

Otherwise, as I don't have a manual I can only guess, but look for a plate of metal (it may even be just a large screw) attached to the main shaft which passes close to, or through, some plastic block (they usually have some form of led light to show when they are detecting). Then, if you turn the shaft by hand to the correct stop position (where the needle is up and the pick up lever is in the home position). Check that the LED light mentioned is on. If the plate is in the correct place but the light is off, the sensor has failed. If the plate is in the wrong place and the light shows as it passes by then the plate should be moved. You can always do a secondary check of the detector by holding a piece of metal next to it.

Do make sure you know what you're doing if you make changes and mark items before you move them, in case you need to put them back, but good luck!
Send a private message to aardvark7 ContactReply & Quote
Old February 2nd, 2017, 08:18 AM   #3 (permalink)
barakaal barakaal is offline
Junior Member
Join Date:
Feb 2017
Posts:
1
Liked:
0 times
Default Re: Prodigi Help!!!

Hello
I have a control panel for prodigi C1201 embroidery and it looks like this.
i have an error reading the disk. can you ensure me that if i buy this panel the error will be cleared??

The error is : NOT SEEK THE TRACK

Process: I install the disquette, select disk managment menu-disk input,... after few second i have the error.

DO you thing changing the panel will solve that??

Thank you.
Send a private message to barakaal ContactReply & Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
Machine Raffle on Facebook (Prodigi B1201C) Stitchitintl.com Product/Service Promotion 0 June 5th, 2014 11:54 AM
Prodigi 2-head PM-1202-CSXL 12-needle 1grtow Used Embroidery Machines 3 April 18th, 2013 07:40 AM
Prodigi Embroidery machines gunner21 Embroidery and Digitizing 0 November 9th, 2012 06:02 PM
Looking for someone to run Prodigi Machine stevenkall Help Wanted 0 September 3rd, 2009 05:32 PM
Prodigi PMC-1201 for sale $10500 innovative415 Old Embroidery Ads 0 February 9th, 2009 11:15 PM

All times are GMT -4. The time now is 04:39 AM.
Copyright © 2011 DigitSmith. All rights reserved.
Forums software by VBulletin, Copyright © 2000-2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.