Flash diagnosing update

inkman996 · September 10th, 2012, 12:33 PM

I replaced it in zone three, I got it in UPS before I seen your post. have to wait till tomorrow to swap it again since I had to let the guys get printing, they were not happy waiting on me all morning lol.

What I mean by the fan is I had one crap out but when looking and messing with the wire feeds it started to work again, so currently all four fans are spinning. Is that cool or do you think replacing is still necessary?

P.S. I do think the relay has helped but I cannot guarantee it till we get involved in a decent sized poly order that requires a full flash. But there is one for this week.

Robert I rechecked the flash height like I told Brian 2" on the front and 2.25" at the rear, I cant raise it any higher because the casing is hitting the bottom of the s/fb assembly.

ScreenShip · September 10th, 2012, 12:41 PM

Quote:

Originally Posted by Binkspot

If my memory serves me right I changed two if not all of the fans on that flash at the instal.

I think you bought a bunch from Grainger on the RockChick install to replace all on one of here flashes so they were of the same brand ... don't think you bought any at inkman's install ... you had your own Printex Group credit card at that time so it shouldn't be to hard to have Colleen go back and check the Printex bank statements if inkman is unsure

ScreenShip · September 10th, 2012, 12:48 PM

I am typing on my Samsung so I just replied within your quoted post ...

Quote:

Originally Posted by inkman996

i replaced it in zone three, i got it in ups before i seen your post. Have to wait till tomorrow to swap it again since i had to let the guys get printing, they were not happy waiting on me all morning lol.

Please swap it with the 4 bulb

what i mean by the fan is i had one crap out but when looking and messing with the wire feeds it started to work again, so currently all four fans are spinning. Is that cool or do you think replacing is still necessary?

Lets just replace them all with grainger ones

p.s. I do think the relay has helped but i cannot guarantee it till we get involved in a decent sized poly order that requires a full flash. But there is one for this week.

Please make sure it is on the 4 bulb circuit

robert i rechecked the flash height like i told brian 2" on the front and 2.25" at the rear, i cant raise it any higher because the casing is hitting the bottom of the s/fb assembly.

if you had the longer stroke that wouldn't be the case

GraphicDisorder · September 10th, 2012, 01:09 PM

Quote:

Originally Posted by ScreenShip

if you had the longer stroke that wouldn't be the case

What are you doing to correct that?

ScreenShip · September 10th, 2012, 01:26 PM

Quote:

Originally Posted by GraphicDisorder

What are you doing to correct that?

GraphicDisorder ... please take your HATE to another thread ... if there is any sincerity in your question (which is doubtful) feel free to start a new thread on the topic (Spiderman out)

GraphicDisorder · September 10th, 2012, 01:27 PM

No hate here, that was as straight forward a question as one can ask.

ScreenShip · September 10th, 2012, 01:32 PM

Quote:

Originally Posted by GraphicDisorder

No hate here, that was as straight forward a question as one can ask.

Awesome ... start a new thread

inkman996 · September 10th, 2012, 01:34 PM

I am pretty sure my press will never have longer heads I gave up hoping on that a long time ago.

ScreenShip · September 10th, 2012, 04:25 PM

Quote:

Originally Posted by inkman996

I am pretty sure my press will never have longer heads I gave up hoping on that a long time ago.

Lets tackle one issue at a time ... otherwise we might get back into face punch mode

we ordered the fans ... will email you when I get the tracking number

Inkworks · September 10th, 2012, 06:45 PM

I may be out to lunch, but wouldn't 4 bulbs wired in parallel run hotter than 3 in parallel?